Home > Error Code > Dlg Diag Error Codes

Dlg Diag Error Codes

Contents

No Errors 0001-0015 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. The drive should now be defect free. Check Floppy and use appropriate diagnostic utility 207 Critical Resource Error Unable to locate and/or use a system resource (e.g. - printer). Replace the drive if the error repeats. weblink

Re-test Drive 220 Drive is Locked Security feature of the drive reports locked status. It also may be due to a defective connection. Replace the drive if the error repeats. At least ten errors have been detected. https://support.wdc.com/KnowledgeBase/answer.aspx?ID=11711

Western Digital Error Code 0007

Re-test Drive 137 Relocated Sector Sector Relocated. Check your floppy and retest. Replace Drive 207 SMART status failed before the media scan.

Please ensure that you are not loading any other DOS level files from the floppy prior to running diagnostic utility. Re-test Drive with appropriate diagnostic utility 205 Aborted By User Test was aborted by the user (Alt-X pressed during a test). Re-test Drive If an error code is encountered that is not in the list above, please Contact Us for additional troubleshooting. 20- Delete Partitions Error Retest after checking the connections.

ECC is a hardware correction technique that corrects errors. Read Element Failure May need to run DLGUDMA to set the drive to a slower speed or replace the IDE cable. Replace drive if unable to correct error 120 NO DRIVE FOUND Cannot communicate with drive. I went back into windows 7 and crystaldiskinfo reported the drive as good and both pending and uncorrectable was 0, however reallocated sectors was still a zero value as well.

Replace the drive if the error repeats. Smart Status Not Available ECC is a hardware correction technique that corrects errors. Replace the drive if the error repeats. Self-Monitoring, Analysis, and Reporting Technology (SMART).

Read Element Failure

This error may have internal and external reasons. https://community.wd.com/t/wd20ears-00s8b1-strange-smart-behavior/14205 Re-Test Drive 110 DRQ NOT EXPECTED The drive did not properly respond to test commands. Western Digital Error Code 0007 There could be media errors present on this drive. Status Code = 07 (failed Read Test Element) Failure Checkpoint = 97 (unknown Test) Ten or more instances of information on data positioning and location could not be found.

Computer runs out of RAM in the... have a peek at these guys The failure to complete the test indicates a failed drive. Re-Test Drive 108 Seek Not Complete A Seek command did not complete in the time allotted. Re-Test Drive 115 ICRC Error Ultra DMA CRC error. Delete Partitions Error Wd

The cable is loose, broken, or not plugged in. This error can occur on non-Western Digital drives. Several instances of track information could not be found. http://darrenmanning.com/error-code/dll-error-codes.html You have to be very patient, the quick type scan came up fast with an error (0132)  then wouldn't let me do anything else.

Re-test Drive 159 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. Too Many Bad Sectors Detected Fix It also may be due to a defective connection. This time I zero wrote the drive which said it successfully completed, but on the extended test it again said errors were found and if I wanted to repair and again

Re-Test Drive 8 Read Sector Failure A Read command during the test has failed.

It also may be due to a defective connection. Drive Reliability Monitor. Replace Drive 208 SMART status failed after the media scan. Dlgdiag Check cabling & retest.

continuum Moderator et Subscriptor Tribus: California Registered: Jul 1, 1999Posts: 79100 Posted: Mon Sep 26, 2011 12:25 pm In reference to original thread:viewtopic.php?f=11&t=1135324 2 posts Ars Technica > Forums > Hardware This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. I used the WRONG version of the Lifeguard diagnostics to test the 6.4GB hard drive - I used the utility that was designed for drivers larger than 8.4GB! http://darrenmanning.com/error-code/dns-323-error-codes.html Check your floppy and retest.

hOW? Drive should be replaced. Re-Test Drive 116 IDNF Error Address Not Found Error.